Loading...
FAQs2025-11-05T11:57:42+11:00

Select your category for faq’s

Are Augers all Pink2025-11-05T12:00:11+11:00

No not all are pink, some are blue, green, gray, white, yellow.  This was to catch your attention!!

Can Hammer Mills be made into a mixing plant?2025-11-05T11:59:58+11:00

Hammer Mills can be combined with Mixers to create a feed processing plant. These plants can also be mounted on load cells.

Power supply?2025-11-05T11:59:51+11:00

The hammer mills can only be supplied with a 3phase motor or optional PTO drive.

How does a hammer mill operate?2025-11-05T12:02:10+11:00

Hammer Mills can be manufactured with either a hay and grain inlet, or a grain hopper only.

Hammer mill consists of a rotor with steel blades that flail out crushing the grain or hay, and forcing it through a perforated screen. The sample can be varied by altering the hole size in the perforated screen.

Can Roller Mills be made into a mixing plant?2025-11-05T12:02:03+11:00

Roller Mills can be combined with Mixers to create a feed processing plant. These plants can also be mounted on load cells.

How does a roller mill operate?2025-11-05T12:01:56+11:00

Grain passes between two fluted rollers. The grain can be lightly rolled, flattened, cracked depending on the gap set between the rollers. The gap can be varied to suit the sample required. Roller mills can crack a variety of grains such as oats, barley, wheat, etc.

What is the difference between a roll mill and a grain crusher?2025-11-05T12:01:50+11:00

The two name are interchangeable. Both machines refer to grain being crushed by rollers.

Can Mixer be made into a mixing plant?2025-11-05T12:01:43+11:00

Stationary mixers can be combined with hammer mills or roller mills to create a feed processing plant. These plants can also be mounted on load cells.

Power supply?2025-11-05T12:01:37+11:00

The mixers can be supplied with a single or 3 phase motor .

What parts need replacing?2025-11-05T12:01:30+11:00

Over time the bearings will wear and the flighting, but these can be easily replaced.

How long does it take to mix the grain?2025-11-05T12:01:24+11:00

Depending on how many ingredients are included in the mix and the mixer size, the mixer will take approximately 5 minutes to mix.
As the seed/grain enters the mixing chamber, the mixing process commences. Therefore when all ingredients have entered the mixer, it only requires a small amount of time to complete the mixing process.

How does a mixer operate?2025-11-05T12:01:19+11:00

The mixer has a central auger which picks up the seed/grain from the base of the mixer and transports it to the top. The seed/grain cascades it over the top and flows back down to the base to be picked up again and repeat the process. Sometimes these mixers are referred to as a fountain blender.

I don’t live in Victoria or Australia so how could I arrange delivery?2025-11-05T12:01:13+11:00

We freight cutters all over Australia at very reasonable rates. We also can arrange freight overseas – just ask.

What does COD mean?2025-11-05T12:01:06+11:00

Goods can be sent immediately & parcel card will be place in your letter box. Take parcel card to your local post office & pay for goods at the post office.  Post office will send payment for goods to Jas Smith.

How can I order spare parts?2025-11-05T12:00:59+11:00

Phone or email request & parts can be sent directly to your address. Payment can be made via pre-arranged cheque, direct deposit or parts can be sent to your post office COD (cash on delivery).

Do you have the parts available?2025-11-05T12:00:52+11:00

All parts are available for the SFC1440, SFC1840 & SFC2340 model chaff cutters, as well as instruction manuals. Most parts are also available for old timber framed Jas Smith 1L, 2A & 4A chaff cutter. Various blade are available to suit various other chaff cutter brands.

What parts usually wear out ?2025-11-05T12:00:40+11:00

Main wearing parts are the blades & the cutting edge – useful life depends on cutting volume & hay quality. These parts are readily available of the shelf and can be posted anywhere.

How hard is it to operate?2025-11-05T12:00:30+11:00

Common sense & safety first are essential when operating the cutter. Simply operated with “U” shaped gear shift – with forward, neutral & reverse gear positions. You do not need to rely on someone with technical know-how to operate. Ease of operation makes it very favourable to use in studs, agistment properties; & by one-person horse owners – male or female.

Do you need special power supply?2025-11-05T12:00:21+11:00

SFC1440 (small cutter) has a 3 pin 240 volt power plug ie. can plug into normal 240 volt socket/household power supply. Larger models are available in single or 3 phase options depending on your power supply (these models need to be wired into your shed by your electrician as each site will have its own requirements)

How often do you have to sharpen the blades?2017-10-09T01:54:49+11:00

Only as required – as blades are made from high quality hardened steel, especially designed to keep their edge. The blades can be sharpened at your local qualified saw sharpening service.

Go to Top